What are your thoughts and feelings about A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't specifically rocket science, yet it does require solid plumbing, carpentry, and often, tiling abilities. Changing an old tub with a brand-new one is additionally a reasonably challenging job. If the old tub is easily easily accessible, the job can relocate immediately; if you need to open up a wall surface to eliminate the old bathtub as well as position the new bath tub, the job is much harder. In either case, the task is within a residence handyman's abilities, although you will need an assistant to leave the old tub and embeded in the new one. See to it you have actually qualified on your own for the task as well as are comfortable trying it. Rather than working with a service provider to take over a halfway-completed task, it is better to take into consideration utilizing one prior to you start. Possibilities are you might require a professional plumber to make tube links.
This post will assist you mount a brand-new bath tub in your restroom if you have actually already purchased a new bathtub and also don't need to transform the setup of your previous supply of water pipelines.
Your tools as well as product list ought to consist of the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is detach the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the limited gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the staying water that will originate from the pipes. When the supply pipelines have been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing compound.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the placing hole in the bath/basin ensuring that the washing machines are in location between the tap and also the sink. Safeguard the faucet in place with the producer given backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap ports. The former kind must be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Tub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wooden boards are valuable in equally spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible tap adapter to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water as well as check all joints and also new pipework for leaks and tighten them if required. Fill the bath tub as well as additionally inspect the overflow outlet and the regular outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the bathtub ought to wait until the bath tub has actually been made use of at least when as this will settle it into its final placement.
Planning for the Setup
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop strain on the tub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you use all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break an inflexible seal, creating the water to permeate the wall in between the bathroom and the tiling, causing difficulties with wetness and possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealer can split rather early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly readily available on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that article about How to Install a Bathtub from an associate on our other website. Liked our piece? Please share it. Let other people discover it. We value reading our article about Tools You Need to Install a New Bathtub .
Need it done? Dial!